Feedwater Heater (Condensing Section 0D)

Feedwater Heater (Condensing Section 0D)#

The condensing feedwater heater is the same as the HeatExchanger model with one additional constraint to calculate the inlet flow rate such that all the entering steam is condensed. This model is suitable for steady state modeling, and is intended to be used with the IAWPS95 property package. For dynamic modeling, the 1D feedwater heater models should be used (not yet publicly available).

Degrees of Freedom#

Usually area and overall_heat_transfer_coefficient are fixed or constraints are provided to calculate overall_heat_transfer_coefficient. If the inlets are also fixed except for the inlet steam flow rate (inlet_1.flow_mol), the model will have 0 degrees of freedom.

Variables#

The variables are the same as HeatExchanger.

Constraints#

In addition to the HeatExchanger constraints, there is one additional constraint to calculate the inlet steam flow such that all steam condenses. The constraint is called extraction_rate_constraint, and is defined below.

\[h_{steam, out} = h_{sat, liquid}(P)\]

Where \(h\) is molar enthalpy, and the saturated liquid enthalpy is a function of pressure.

FWHCondensing0D Class#

class idaes.models_extra.power_generation.unit_models.feedwater_heater_0D.FWHCondensing0D(*args, **kwds)#

Feedwater Heater Condensing Section The feedwater heater condensing section model is a normal 0D heat exchanger model with an added constraint to calculate the steam flow such that the outlet of shell is a saturated liquid.

Args:

rule (function): A rule function or None. Default rule calls build(). concrete (bool): If True, make this a toplevel model. Default - False. ctype (class): Pyomo ctype of the block. Default - pyomo.environ.Block

Config args

dynamic

Indicates whether this model will be dynamic or not, default = useDefault. Valid values: { useDefault - get flag from parent (default = False), True - set as a dynamic model, False - set as a steady-state model.}

has_holdup

Indicates whether holdup terms should be constructed or not. Must be True if dynamic = True, default - False. Valid values: { useDefault - get flag from parent (default = False), True - construct holdup terms, False - do not construct holdup terms}

hot_side_name

Hot side name, sets control volume and inlet and outlet names

cold_side_name

Cold side name, sets control volume and inlet and outlet names

hot_side

A config block used to construct the hot side control volume. This config can be given by the hot side name instead of hot_side.

hot_side
material_balance_type

Indicates what type of mass balance should be constructed, default - MaterialBalanceType.useDefault. Valid values: { MaterialBalanceType.useDefault - refer to property package for default balance type **MaterialBalanceType.none - exclude material balances, MaterialBalanceType.componentPhase - use phase component balances, MaterialBalanceType.componentTotal - use total component balances, MaterialBalanceType.elementTotal - use total element balances, MaterialBalanceType.total - use total material balance.}

energy_balance_type

Indicates what type of energy balance should be constructed, default - EnergyBalanceType.useDefault. Valid values: { EnergyBalanceType.useDefault - refer to property package for default balance type **EnergyBalanceType.none - exclude energy balances, EnergyBalanceType.enthalpyTotal - single enthalpy balance for material, EnergyBalanceType.enthalpyPhase - enthalpy balances for each phase, EnergyBalanceType.energyTotal - single energy balance for material, EnergyBalanceType.energyPhase - energy balances for each phase.}

momentum_balance_type

Indicates what type of momentum balance should be constructed, default - MomentumBalanceType.pressureTotal. Valid values: { MomentumBalanceType.none - exclude momentum balances, MomentumBalanceType.pressureTotal - single pressure balance for material, MomentumBalanceType.pressurePhase - pressure balances for each phase, MomentumBalanceType.momentumTotal - single momentum balance for material, MomentumBalanceType.momentumPhase - momentum balances for each phase.}

has_phase_equilibrium

Indicates whether terms for phase equilibrium should be constructed, default = False. Valid values: { True - include phase equilibrium terms False - exclude phase equilibrium terms.}

has_pressure_change

Indicates whether terms for pressure change should be constructed, default - False. Valid values: { True - include pressure change terms, False - exclude pressure change terms.}

property_package

Property parameter object used to define property calculations, default - useDefault. Valid values: { useDefault - use default package from parent model or flowsheet, PropertyParameterObject - a PropertyParameterBlock object.}

property_package_args

A ConfigBlock with arguments to be passed to a property block(s) and used when constructing these, default - None. Valid values: { see property package for documentation.}

cold_side

A config block used to construct the cold side control volume. This config can be given by the cold side name instead of cold_side.

cold_side
material_balance_type

Indicates what type of mass balance should be constructed, default - MaterialBalanceType.useDefault. Valid values: { MaterialBalanceType.useDefault - refer to property package for default balance type **MaterialBalanceType.none - exclude material balances, MaterialBalanceType.componentPhase - use phase component balances, MaterialBalanceType.componentTotal - use total component balances, MaterialBalanceType.elementTotal - use total element balances, MaterialBalanceType.total - use total material balance.}

energy_balance_type

Indicates what type of energy balance should be constructed, default - EnergyBalanceType.useDefault. Valid values: { EnergyBalanceType.useDefault - refer to property package for default balance type **EnergyBalanceType.none - exclude energy balances, EnergyBalanceType.enthalpyTotal - single enthalpy balance for material, EnergyBalanceType.enthalpyPhase - enthalpy balances for each phase, EnergyBalanceType.energyTotal - single energy balance for material, EnergyBalanceType.energyPhase - energy balances for each phase.}

momentum_balance_type

Indicates what type of momentum balance should be constructed, default - MomentumBalanceType.pressureTotal. Valid values: { MomentumBalanceType.none - exclude momentum balances, MomentumBalanceType.pressureTotal - single pressure balance for material, MomentumBalanceType.pressurePhase - pressure balances for each phase, MomentumBalanceType.momentumTotal - single momentum balance for material, MomentumBalanceType.momentumPhase - momentum balances for each phase.}

has_phase_equilibrium

Indicates whether terms for phase equilibrium should be constructed, default = False. Valid values: { True - include phase equilibrium terms False - exclude phase equilibrium terms.}

has_pressure_change

Indicates whether terms for pressure change should be constructed, default - False. Valid values: { True - include pressure change terms, False - exclude pressure change terms.}

property_package

Property parameter object used to define property calculations, default - useDefault. Valid values: { useDefault - use default package from parent model or flowsheet, PropertyParameterObject - a PropertyParameterBlock object.}

property_package_args

A ConfigBlock with arguments to be passed to a property block(s) and used when constructing these, default - None. Valid values: { see property package for documentation.}

delta_temperature_callback

Callback for for temperature difference calculations

flow_pattern

Heat exchanger flow pattern, default - HeatExchangerFlowPattern.countercurrent. Valid values: { HeatExchangerFlowPattern.countercurrent - countercurrent flow, HeatExchangerFlowPattern.cocurrent - cocurrent flow, HeatExchangerFlowPattern.crossflow - cross flow, factor times countercurrent temperature difference.}

initialize (dict): ProcessBlockData config for individual elements. Keys

are BlockData indexes and values are dictionaries with config arguments as keys.

idx_map (function): Function to take the index of a BlockData element and

return the index in the initialize dict from which to read arguments. This can be provided to override the default behavior of matching the BlockData index exactly to the index in initialize.

Returns:

(FWHCondensing0D) New instance

FWHCondensing0DData Class#

class idaes.models_extra.power_generation.unit_models.feedwater_heater_0D.FWHCondensing0DData(component)[source]#
build()[source]#

Building model

Parameters:

None

Returns:

None

initialize_build(*args, **kwargs)[source]#

Use the regular heat exchanger initialization, with the extraction rate constraint deactivated; then it activates the constraint and calculates a steam inlet flow rate.